Yes, the components of an RF dielectric lens can be injection moulded. Plastic-IT has moulded them in production, holding a 50 micron tolerance on the moulded geometry.
A moulded part is not a finished lens on its own. After moulding, a homogenisation process brings the individual components together into a single unit.
The development takes more work up front than most moulded parts. Once the material, tool and process are proven, the moulding runs like any other injection moulding job.
Do you need moulded RF lenses?
If your antenna, radar or communications product uses a dielectric lens and you need more than a handful, injection moulding is usually the right way to make the parts.
- Machining them one at a time is slow and wasteful.
- 3D printing suits prototypes. It is slower per part and less dimensionally accurate than injection moulding.
- A moulding tool makes every part the same shape, shot after shot. That matters when an array needs every lens to behave the same.
We can make them.
Can they actually be moulded?
Yes. The parts are moulded from a thermoplastic filled with ceramic powder. The filler raises the dielectric constant to the value the RF design needs.
The approach is not new. Murata's patent US6489928, filed in 2001, describes a lens antenna injection moulded from a ceramic filled thermoplastic. It states that the lens body "is generally molded by injection molding from the viewpoint of molding cost and molding precision".
This is work Plastic-IT has already carried out, from development through to production.
What we have produced
- Moulded components: several per lens. How many depends on the type and size of the lens.
- Tolerance on the moulded geometry: 50 microns (0.05 mm)
- Tolerance on the complete lens assembly: 200 microns (0.2 mm)
- Verified by: CT scanning, X-ray scanning and laser scanning
From components to a finished lens
A lens does not come out of the tool finished. Moulding produces the individual components. A homogenisation process then brings them together into a single unit. That step needs the same care as the moulding itself.
Plastic-IT has run that process alongside the moulding, so we can supply finished lenses rather than a box of moulded parts.
How the lenses are verified
A moulded lens is only useful if you can show it will perform. Verification uses CT scanning, X-ray scanning and laser scanning to:
- make sure there are no voids or cracks
- confirm dimensional accuracy
- correlate what is measured with the RF performance of the lens
The last point matters most. A scan is only worth taking if it tells you how the lens will behave.
Are they hard to mould?
At the start, yes. Most of the effort goes into development before the first good part.
- Getting the material right. The compound has to meet two separate targets: the dielectric constant, set mainly by filler loading, and low loss, which depends on the base polymer, filler grade and dispersion.
- Designing the tool. Gate position and flow decide whether the filler ends up evenly spread through the part. Uneven filler means an uneven lens.
- Thick sections. Lens parts tend to be thicker than normal moulded walls, so they want to sink on the surface and void inside. A void is a pocket of air in the signal path.
- Shrinkage. The lens works because of its exact profile. The tool has to allow for how the part shrinks so the profile comes out right.
- Wear. Ceramic filler is abrasive, so the tool and screw have to be built for it.
Moldflow simulation is part of our DFM process. We use it to check the filling characteristics, post-mould shrinkage and identify any potential for warpage before any steel is cut.
Once it is set up
We run lens components using scientific moulding. The process window is established through structured trials and documented. Key process parameters are monitored every shot, so any drift is caught before it affects a part. That control gives the shot-to-shot consistency an RF lens depends on.
Accreditations
Plastic-IT is ISO 9001:2015 certified (certificate 19/1185, issued by Centre for Assessment, UKAS 0120) and registered on JOSCAR.
JOSCAR is the supplier due diligence system for the UK aerospace, defence and security sectors. A great deal of RF lens work comes through those supply chains, which is why the registration matters for it.
What we need to get started
- The lens model, ideally as a STEP file
- The dielectric constant and loss you need (or the frequency and performance you are designing for)
- Rough quantities
Send it to us and we will tell you what it would take.
FAQs
Does a moulded lens come out of the tool finished?
No. Moulding makes the components. A homogenisation process then brings them together into a single unit. Plastic-IT has run both stages in production.
Is injection moulding better than 3D printing for RF lenses?
For prototypes, printing is quicker to start. For production, injection moulding is more dimensionally accurate and every part comes out the same.
What tolerance can a moulded RF lens be held to?
On the lenses Plastic-IT has produced, 50 microns on the moulded geometry and 200 microns on the complete lens assembly. The right figure for a new lens depends on its type, size and frequency.
How is a moulded RF lens checked?
With CT, X-ray and laser scanning. The scans rule out voids and cracks, confirm the dimensions and are correlated with the RF performance of the lens.
What plastic are moulded RF lenses made from?
A thermoplastic filled with ceramic powder. The base polymer and the amount of filler are chosen to give the dielectric constant the design needs.
Can you make a lens to our own design?
Yes. Send us the model and the RF targets. We will look at it before any tool is made.